USB Load Tester 150W 200V 20A Resistor Adjustable Constant Current Electronic Load Tester Battery Capacity Tester Module Intelligent Discharge Resistance Power Tester
Parameters:
Input Interface / Output Interface: 100A High Current Bite Screw Stud
Voltage measurement range: 0.00V ~ 200V, resolution accuracy: 0.01V
Current measurement range: 0.00A ~ 20A, resolution accuracy: 0.01A
Capacity accumulation range: 0 ~ 999.999Ah, resolution accuracy: 0.01Ah
Power accumulation range: 0 ~ 9999.9Wh, resolution accuracy: 0.01Wh
Power measurement range: 0000.00 ~ 150W, resolution accuracy: 0.01W
Impedance measurement range: 1 ~ 999.9 Europe, resolution accuracy: 0.01 Europe
Temperature measurement range: 0 ~ 99 ℃, resolution accuracy: 1 ℃
Timing maximum time: 999 hours 59 minutes 59 seconds, resolution accuracy: 1 second
Refresh time: > 500mS / times
Measurement rate: about 0.5 times / sec
Overvoltage overcurrent set the alarm mode: show alert interface to remind the user
Overpressure reminder setting range: 1 ~ 200V
Low voltage reminder setting range: 0 ~ 190V
Overflow reminder set range: 0.2 ~ 100A
Product size: 156mm * 96mm * 58mm
Operating temperature: -10 ~ +60 ℃
Working humidity: 10 ~ 80 (no doubt)
Working pressure: 80 ~ 106kPa
Note:
Exceeding the specified power will burn the product.
The USB function of this load meter is to connect the trigger equipment
The current cannot be adjusted via USB, and it is adjusted by the knob on the load meter
Including
1 * 150W USB Adjustable Constant Current Load Tester
- Prevent burning warning: when the input voltage battery and large power test, access must be beforeusing two current adjustment knob counterclockwise to the minimum to zero, then the access, accordingto the priority according to current power to slowly adjust current knob, must not instantly transferred infull, so there are excessive instantaneous power load discharge tube burnt huge risk! Please use thespecial attention to this point, thank you!
- Two power supply methods: 1. DC6-12V DC5.0 power supply; 2. DC6-12V Micro USB power supply.The body discharge power cannot exceed 150W, otherwise there is a risk of burnout.
- Voltage measurement range: 0.00V ~ 200V, Current measurement range: 0.00A ~ 20A.
- How to operate: Set the capacity, power, time using the Keystrokes method Reset:1. Reset button Long all data (mAh, Klitschko, 00: 00: 00); 2. Fast button twice capacity reset (mAh); 3. Fast button three power reset (ㅁ);4. Fast button Four time reset (00:00:00); 5. Fast button five settings auto standby, Discharge count down regularly; 6. No load output No load, fast seven key, And current zero zero current, Environmental temperature Accurate calibration.
- 150W power refers to: In accordance with the power calculation formula P = UI (power = voltage x current); 10V input Approximately 18A discharge current 20V input Approximately 9A discharge current 30V input Approximately 6A discharge current.
- Prevent burning warning: when the input voltage battery and large power test, access must be beforeusing two current adjustment knob counterclockwise to the minimum to zero, then the access, accordingto the priority according to current power to slowly adjust current knob, must not instantly transferred infull, so there are excessive instantaneous power load discharge tube burnt huge risk! Please use thespecial attention to this point, thank you!
- Two power supply methods: 1. DC6-12V DC5.0 power supply; 2. DC6-12V Micro USB power supply.The body discharge power cannot exceed 150W, otherwise there is a risk of burnout.
- Voltage measurement range: 0.00V ~ 200V, Current measurement range: 0.00A ~ 20A.
- How to operate: Set the capacity, power, time using the Keystrokes method Reset:1. Reset button Long all data (mAh, Klitschko, 00: 00: 00); 2. Fast button twice capacity reset (mAh); 3. Fast button three power reset (ㅁ);4. Fast button Four time reset (00:00:00); 5. Fast button five settings auto standby, Discharge count down regularly; 6. No load output No load, fast seven key, And current zero zero current, Environmental temperature Accurate calibration.
- 150W power refers to: In accordance with the power calculation formula P = UI (power = voltage x current); 10V input Approximately 18A discharge current 20V input Approximately 9A discharge current 30V input Approximately 6A discharge current.
