JANSANE SCT-013-000 100A Non-invasive AC Current Sensor Split-Core Clamp Current Transformer;
JANSANE SCT-013-000 100A Non-invasive AC Current Sensor Split-Core Clamp Current Transformer

Specification
Model: SCT-013-000
Type: Non-invasive current transformer
Core Material: Ferrite
Input Current: 0~100A AC
Output Mode: 0~50mA
Leading Wire in Length: 1m
Turns Ratio: 1: 1800

Buy Now From Amazon

Specification
Model: SCT-013-000
Type: Non-invasive current transformer
Core Material: Ferrite
Input Current: 0~100A AC
Output Mode: 0~50mA
Leading Wire in Length: 1m
Turns Ratio: 1: 1800
Work Voltage: 660 v
Resistance Grade: Grade B
Max Sampling Resistance: 10 Ω
Linearity: ±3%
Accurancy: ±1%
Work Frequency: 50-1 KHz
Work Temperature: -25˚C ~ 70˚C
Reference project: Open Energy Monitor
Dielectric Strength: 6000V AC/1min
Opening Size: 0.51 * 0.51inch / 13 x 13mm
Two Form of Output: current output or voltage output (a burden resistor needed to add);
Mechanical strength: opening and closing times, no less than 1000 times (20 ℃)
High Quality and Safe: Meet the requirement of flame-retardant characteristics (UL94-V0)


100% Satisfaction Guarantee
12-Month Warranty; No satisfied ,Free reason for return; We could also resend you new one due to quality problem.

  • This SCT-013-000 ac current sensor used for measuring alternating current, particularly used for whole building consumption or generation.
  • This split core current transformer is particularly suitable for DIY use and it works well with arduino and raspberry pi.
  • Use this 100a current sensor to build your own energy monitor, reducing your power usage, or use it build an over-current protection device for an AC load.
  • Input Current: 100a AC; Length of Leading Wire: 1m; Two Form of Output: current output or voltage output (burden resistor needed to add); Cable Jack: 3.5mm (like a headphone jack).
  • Suitable for lighting equipment, AC motors, air compressors, monitoring, current measurement and over-current protection.
  • This SCT-013-000 ac current sensor used for measuring alternating current, particularly used for whole building consumption or generation.
  • This split core current transformer is particularly suitable for DIY use and it works well with arduino and raspberry pi.
  • Use this 100a current sensor to build your own energy monitor, reducing your power usage, or use it build an over-current protection device for an AC load.
  • Input Current: 100a AC; Length of Leading Wire: 1m; Two Form of Output: current output or voltage output (burden resistor needed to add); Cable Jack: 3.5mm (like a headphone jack).
  • Suitable for lighting equipment, AC motors, air compressors, monitoring, current measurement and over-current protection.

Similar Products

3.5mm Stereo Female terminal block panel mount connector 2 packSMAKN Voltage Transformer Module Active Single Phase Voltage Sensor Module AC OutputCurrent Transformer, DROK 100A 100mA AC Current Sensor, Split Core Amp Transformer Sensing Relay, Mini Clip-on Easy to Install CT Without Power OffHiLetgo 3pcs ESP8266 NodeMCU CP2102 ESP-12E Internet WiFi Development Board Open Source Serial Wireless Module Works Great with Arduino IDE/Micropython (Large)HiLetgo ESP-WROOM-32 ESP32 ESP-32S Development Board 2.4GHz Dual-Mode WiFi + Bluetooth Dual Cores Microcontroller Processor Integrated with Antenna RF AMP Filter AP STA for Arduino IDEIZOKEE D1 Mini NodeMcu Lua 4M Bytes WLAN WiFi Internet Development Board Base on ESP8266 ESP-12F for Arduino, 100% Compatible with WeMos D1 Mini (Pack of 3)massmall 30Pieces 2 Pin 5mm Pitch PCB Mount Screw Terminal Block Connector 250V 8A(Green)AUSTOR 100 Pcs PCB Board Kit Including 30 Pcs PCB Boards 30 Pcs 40 Pin 2.54mm Header Connector(Bonus: 10 Pcs 2P&3P Terminal Blocks and 30 Pcs Caps)