Electronic Speed Controller Specifications:
  Cont. Current: 60A
  Burst Current: 360A
  Battery: 2-3 Cells Lipo / 4-9 Cells NiMh
  BEC Output: 5.8V/3A (Switch Mode)
  Power Supply Plugs: T Male
  Motor Plugs: Female 4mm Bullet Connector
  Motor Type:
    For 2s Lipo or 6 cells NiMH:
    On-road: 3660-size or smaller motor with the KV<6000
    Off-road / Buggy / Monster: 3660-size or smaller motor with the KV<4000
    For 3s Lipo or 9 cells NiMH:
    On-road: 3660-size or smaller motor with the KV<4000
    Off-road / Buggy / Monster: 3656-size or smaller motor with the KV<3000
  Size: 50.8 * 38.5 * 36.5mm
  Weight: 91g / 3.2oz
Note:
1 The combo is waterproof for slight water. Don't put the ESC into water for a long time which may cause the fan burns.
2 Contact us to purchase the specified program card if you need.
Packing included:
1 * 60A Brushless ESC
Never leave this product unsupervised when it is powered on. It's important to select the battery, Not all motor and ESC suitable for 3s lipo, It is better for 2s lipo. A wrong tooth ratio can cause the motor to overheat. The motor temperature should be lower than 212℉ during the operation. Temperatures above 212℉ will weaken the magnet and may partly melt the coils and eventually damage the ESC (because of strong current)!!! To avoid potential risks such as ESC/motor damage or malfunction caused by overheat, start with a very small pinion first and check the ESC & motor temperatures regularly throughout the run. This is the only way to prevent overheat!!!!- The ESC is built-in 5.8V/3A BEC which can power receiver or other suitable equipment. There is no need to set throttle range before usage. A good choice for your RC car! For better user experience, 3S battery is not recommended for ESA below 120A.
- Specially designed for RC car with excellent start-up,acceleration and linearity features,Compatible with sensorless brushless motor.
- Multiple protection features,low voltage cut-off protection for lithium or nickel battery/Over-heat protection/Throttle signal loss protection/Motor blocked protection. The strong resistant current capability,excellent heat dissipation,Easily programmed and compatible with pocket-sized program card. Water-proof and dust-proof for all-weather races,Note:please uninstall the cooling fan before using this ESC in water,clean and dry it soon after the use for avoiding the connectors get tusty.
- Never leave this product unsupervised when it is powered on. It's important to select the battery, Not all motor and ESC suitable for 3s lipo, It is better for 2s lipo.
- A wrong tooth ratio can cause the motor to overheat. The motor temperature should be lower than 212℉ during the operation. Temperatures above 212℉ will weaken the magnet and may partly melt the coils and eventually damage the ESC (because of strong current)!!! To avoid potential risks such as ESC/motor damage or malfunction caused by overheat, start with a very small pinion first and check the ESC & motor temperatures regularly throughout the run. This is the only way to prevent overheating!!!
- The ESC is built-in 5.8V/3A BEC which can power receiver or other suitable equipment. There is no need to set throttle range before usage. A good choice for your RC car! For better user experience, 3S battery is not recommended for ESA below 120A.
- Specially designed for RC car with excellent start-up,acceleration and linearity features,Compatible with sensorless brushless motor.
- Multiple protection features,low voltage cut-off protection for lithium or nickel battery/Over-heat protection/Throttle signal loss protection/Motor blocked protection. The strong resistant current capability,excellent heat dissipation,Easily programmed and compatible with pocket-sized program card. Water-proof and dust-proof for all-weather races,Note:please uninstall the cooling fan before using this ESC in water,clean and dry it soon after the use for avoiding the connectors get tusty.
- Never leave this product unsupervised when it is powered on. It's important to select the battery, Not all motor and ESC suitable for 3s lipo, It is better for 2s lipo.
- A wrong tooth ratio can cause the motor to overheat. The motor temperature should be lower than 212℉ during the operation. Temperatures above 212℉ will weaken the magnet and may partly melt the coils and eventually damage the ESC (because of strong current)!!! To avoid potential risks such as ESC/motor damage or malfunction caused by overheat, start with a very small pinion first and check the ESC & motor temperatures regularly throughout the run. This is the only way to prevent overheating!!!
