Specifications:
Input DC 12V
Length approx. 18 inches (45cm)
Notice Before Purchase
Read the manual of your mixer device and check the data sheet.
Then choose what you need according to the positive and negative pole of our LED light needles.
If the LED light cannot match the corresponding needle of your equipment, please don't make purchase, because you will need to re-welding it by yourself which requires professional technology knowledge.
In this case, we recommend our New Arrival Product : Automatic Series - Automatically adjust the voltage(5.5V-16V), distinguish between positive and negative pole, Suitable for most of Musical Console Mixer.
-Rejea 5.5V-16V Voltage Automatically Adjustable LED Console Lamp
Note: This lamp will not work on Normal 3 Pin XLR/ 4 Pin XLR/ BNC connectors( because of Volt issue), make sure your mixing console has the Specific 12-Volt Task Light Connector for this led lamp.
Q: How does this lamp work?
A: Consoles require a dedicated 12-volt task light connector for use of this lamp. So this lamp will not operate on a phantom powered mic input. Because the standard for phantom power is +48 volts applied to BOTH sides of the audio signal pair through two resistors, with the V- connected to ground and shield, too high for efficiently driving LED.
Durable & long-lasting LEDs, High efficiency more light for less energy.
Cool operating temperatures adjust without burning your fingers.
Have tested with following models
4 Pin XLR
Behringer X32
Midas M32
BNC connector
Crest 12M
SOUNDKING AS3208, MIX32AU
Peavey CD MIX 7032A VENUE SC48, Screen Pro2,
Mackie Onyx 24.4 console
USB
Soundcraft Si Impact
- [ SUITABLE FOR ] - Compatible with Behringer X2442USB, Behringer Eurodesk MX9000, Furman with rear-mounted BNC light connector, Mackie PA Board, Mackie 1604, Mackie Onyx 24.4 Console, SOUNDKING AS3208, MIX32AU, Screen Pro2. You need to swivel (mostly to the right) to lock on the connector to keep it upright on the plug base firmly without falling.
- [ NOT FOR ] - Mackie VLZ Pro mixing console, Furman Power Conditioner, Crest 12m mixer. Some might need swivel as it is NOT good for vertical install. Gravity spins light and arm at BNC connection.
- [ MUCH MORE LIGHT ] - 12VAC LED Lamp for Mixers (Low Voltage Power). White Light.
- [ NOTE FOR BNC CONNECTOR ] - Swivel to LOCK if it is loose on your device. ONLY on Specific 12-Volt Task Light Socket. Please let us know your mixer model before returning the product if the item is loose on your connector or it could not turn on, as it dose NOT fit ALL models. Consult before Click-N-Purchase is much appreciated.
- [ EFFICIENT ILLUMINATION ] - Long lasting LED lights that rarely need replacing, 12 inches in length.
- [ SUITABLE FOR ] - Compatible with Behringer X2442USB, Behringer Eurodesk MX9000, Furman with rear-mounted BNC light connector, Mackie PA Board, Mackie 1604, Mackie Onyx 24.4 Console, SOUNDKING AS3208, MIX32AU, Screen Pro2. You need to swivel (mostly to the right) to lock on the connector to keep it upright on the plug base firmly without falling.
- [ NOT FOR ] - Mackie VLZ Pro mixing console, Furman Power Conditioner, Crest 12m mixer. Some might need swivel as it is NOT good for vertical install. Gravity spins light and arm at BNC connection.
- [ MUCH MORE LIGHT ] - 12VAC LED Lamp for Mixers (Low Voltage Power). White Light.
- [ NOTE FOR BNC CONNECTOR ] - Swivel to LOCK if it is loose on your device. ONLY on Specific 12-Volt Task Light Socket. Please let us know your mixer model before returning the product if the item is loose on your connector or it could not turn on, as it dose NOT fit ALL models. Consult before Click-N-Purchase is much appreciated.
- [ EFFICIENT ILLUMINATION ] - Long lasting LED lights that rarely need replacing, 12 inches in length.
