BETAFPV FPV FC F3 EVO Brushed Whoop Flight Controller Brushed Long Range Version with Native Frsky Receiver

Specifications:
CPU: STM32F303CCT6
Six-Axis: MPU6500
Size: 26mm x 26mm,fully com...

Buy Now From Amazon

BETAFPV FPV FC F3 EVO Brushed Whoop Flight Controller Brushed Long Range Version with Native Frsky Receiver

Specifications:
CPU: STM32F303CCT6
Six-Axis: MPU6500
Size: 26mm x 26mm,fully compatible with the Inductrix quad frame and mounting pattern
Firmware version: Betaflight SPRACINGF3EVO 3.1.6
Receiver: Frsky D8 potocol with PA
Weight: 2.8g
Guidance: https://betafpv.freshdesk.com/support/solutions/folders/27000050814

Frsky Receiver:
Currently the built in Frsky receiver is compatible with Taranis, Taranis Plus, X9E, Horus X12S, XJT Modules with International Firmware.
This built in receiver integrate a power amplifier IC (PA) RFX2401C, so you could get up to 1 kilometers long range. This is the biggest improvement than other board with no PA included. Also this receiver supports RSSI telemetry.

Package:
1 * F3 EVO brushed flight controller ( 55mm PH-JST 2.0 power cable soldered)
4 * M1.2x4mm screws (Fit for stock Inductrix frame)
4 * M1.4x5mm screws (Fit for Beta75 etc 75mm frame)
4 * Ruber dampers
1 * 55mm PH-JST 1.25 power cable pigtail

  • Fully programmable through Betaflight, using the onboard USB port, tune all the parameters, PID's, and rates to your perfect settings
  • Some basic guidance and typical FAQ, please check it here : https://betafpv.freshdesk.com/support/solutions
  • Built in Frsky D8 protocol native receiver, compatible with almost ALL Frsky radios(e.g. Taranis X9D/X9D Plus/X7) or Frsky compatible transmitter module
  • With PA integrated, up to 0.5 Kilometers long range, with RSSI telemetry
  • The flight controller board comes pre-flashed with Betaflight firmware, and pre-soldered 55mm power cable pigtail with JST-PH 2.0 connector, AKA PowerWhoop connector. Designed to work with current Tiny Whoop or Blade Inductrix setups
  • Fully programmable through Betaflight, using the onboard USB port, tune all the parameters, PID's, and rates to your perfect settings
  • Some basic guidance and typical FAQ, please check it here : https://betafpv.freshdesk.com/support/solutions
  • Built in Frsky D8 protocol native receiver, compatible with almost ALL Frsky radios(e.g. Taranis X9D/X9D Plus/X7) or Frsky compatible transmitter module
  • With PA integrated, up to 0.5 Kilometers long range, with RSSI telemetry
  • The flight controller board comes pre-flashed with Betaflight firmware, and pre-soldered 55mm power cable pigtail with JST-PH 2.0 connector, AKA PowerWhoop connector. Designed to work with current Tiny Whoop or Blade Inductrix setups

Similar Products

Crazepony 4pcs 6x15mm Motor (Speed: Insane) 19000KV for Blade Inductrix Tiny Whoop Micro JST 1.25 Plug with Rubber RingsBETAFPV Beta65S 65mm Whoop Frame with 7x16mm 17500KV Brushed Motors Upgrade Version for LED LightCrazepony FPV Micro AIO Camera 5.8G 48CH 25mW Transmitter with Y Splitter for FPV Drone like Blade Inductrix etcBETAFPV 3 Sets 6x15mm Tiny Whoop Motor 19500KV (Speed: Insane) for Blade InductrixWolfwhoop WT05 Micro AIO 600TVL Camera Only 3.4g 5.8GHz 25mW FPV Transmitter with Dipole Brass Antenna Combo for FPV Quadcopter DroneCrazepony Mini Quadcopter Frame Kit with Props Removal Tool for Tiny Whoop Eachine E010 JJRC H36 QuadcopterBETAFPV F3 V1.1 Brushed Flight Controller Integrated with OSD and Frsky Receiver (SBUS)BETAFPV 2pcs Beta65S 65mm Whoop Frame Kit Upgrade Version for LED Light Compatible for 7X16mm Motor