HOBBYMATE 15A ESCs have all the performance you would hope for and you will struggle to find a frame small enough to fit these
ESCs and they will still give you plenty of headroom on a standard 180 210 250 size quad!

Buy Now From Amazon

HOBBYMATE 15A ESCs have all the performance you would hope for and you will struggle to find a frame small enough to fit these
ESCs and they will still give you plenty of headroom on a standard 180 210 250 size quad!
Oneshot125 is a different and faster communication protocol between the flight controller and the ESC on your quadcopter.
It allows the FC to send control commands to the motor quicker, therefore in theory your multirotor should perform better.
Damped mode
This feature allows your motors to respond to throttle decreases much quicker, allowing for more stable flying, and higher
response to throttle decreases.
Easy upgrades
With the BLHELI software rapidly evolving, you can flash the lastest firmware using the 3pin connector and suitable USB adapter
and now can be used via the cleanflight GUI
please note you will need to be running the Betaflight firmware to connect via the cleanflight interface but this is a simple way
of adjusting and tweaking the settings of your escs.

Specification :
Input: 2-4s Lipo
Constant: 15 Amps
Burst: 25 Amps
Weight: 4g bare board
Dimensions: 23x12.5x3mm
Motor wire: 70mm
Signal wire: 120mm
PCB - 4 Layer Blind hole PCB - 3oz Pour
Mosfet: N-Channel
OneShot and BLHeli 16.2 Pre Installed

Package Includes:
4 * HOBBYMATE 15A Mini ESC Oneshot125 Electronic Speed Controller 2-4S Brushless for FPV Multicopter


  • Based on BLHeli firmware with low voltage protection, over heat protection and self check functions
  • Works with 2S to 4S input - Rated at 15A continuous and 25A burst
  • Perfect for 1806 2204 2205 brushless motor in QAV180 QAV 210 QAV250 and other small drone
  • Support OneShot ultra-high speed control and Bi-directional rotating. All N-FET design with external oscillator for steady performance across different thermal and voltage conditions.
  • WARNING: when upgrading firmware, always select "BlueSeries 12a" type firmware otherwise ESC may be permanently damaged & WARNING: Take great care to ensure the ESC input power is wired correctly as improper connections will permanently damage the ESC when first connecting the battery
  • Based on BLHeli firmware with low voltage protection, over heat protection and self check functions
  • Works with 2S to 4S input - Rated at 15A continuous and 25A burst
  • Perfect for 1806 2204 2205 brushless motor in QAV180 QAV 210 QAV250 and other small drone
  • Support OneShot ultra-high speed control and Bi-directional rotating. All N-FET design with external oscillator for steady performance across different thermal and voltage conditions.
  • WARNING: when upgrading firmware, always select "BlueSeries 12a" type firmware otherwise ESC may be permanently damaged & WARNING: Take great care to ensure the ESC input power is wired correctly as improper connections will permanently damage the ESC when first connecting the battery

Similar Products

Matek Systems PDB XT60 Power Distribution Board BEC 5V 2A 12V 0.5A with XT60 Plug for DIY Quadcopter Output Support 6 ESC for X or H Design FPV Racing QuadRJXHOBBY SP Racing F3 Flight Controller Acro 6 DOF for RC Multicopter for DIY Mini 180 190 195 210 220 250 280 300 330 RC DroneFloureon 2 Packs 3S 11.1V 1500mAh 35C RC Lipo Battery with XT60 Plug for RC Car, Skylark m4-fpv250, Mini Shredder 200, Qav250, Vortex, Drone and FPV (2.91 x 1.46 x 1.08 Inch)HOBBYMATE BLHeli-15A-ESC-Speed-Controller for 180-210-250 Racing-RC-Quadcopter Multicopter (Pack of 1 )HOBBYMATE 180Pcs Assorted M3 Nylon Screws Nut Standoffs Spacers for DIY Building of FPV RC Quadcopter Drone, PC modsMakerfire 4pcs ESC 20A BLHeli Brushless Speed Controller for QAV250 Racing DroneHOBBYMATE FPV Racing Quadcopter Motor ESC Combo - 2 Pairs CW CCW 2204 2300KV Plus 4 PCS BLHeli 15A ESC, Support 2-4SNIDICI 50pcs FPV Sponge Mat Landing Pad Anti-vibration Foam Sticky Tape for X QAV-X Quadcopter Multicopter Frame