Tired of unwanted substances getting into your precious retrofit lighting assemblies? These rubber housing seal caps conveniently seal out any water condensation, moisture, dust, and more from your retrofit lights to keep all the lights working. These rubber caps protect your xenon LED conversion kits, aftermarket LED headlights, retrofit headlights and more so you can have peace of mind that your lights will be long lasting.
There's no holes in the cap so you can poke a custom hole for the wiring go to through.
Universal for most vehicles:
Acura Integra MDX NSX RDX RSX TL TLX TSX
Audi A3 A4 A5 A6 Q5 Q7
BMW 1 2 3 4 5 6 7 series X1 X3 X5 X6 Z4
Cadillac CTS Escalade
Chevrolet Avalanche Camaro Colorado Corvette Cruze Malibu Silverado 1500 2500 3500 Tahoe
Dodge Challenger Charger Dart Durango Neon Nitro Ram
Ford Edge Escape Explorer F-150 F-250 F-350 Fiesta Flex Focus Fusion Mustang
GMC Canyon Denali Sierra Yukon
Honda Accord Civic CR-V CR-Z Element Fit Pilot S2000
Hyundai Genesis Santa Fe Sonata Tiburon
Infiniti EX35 FX35 FX45 FX50 G35 G37 M45 M35 M37 M45 M56 Q50 Q60 QX56 QX60 QX70 QX80
Jeep Grand Cherokee Liberty Wrangler
Lexus CT ES GS GX HS IS LS LX RX
Mazda 2 3 5 6 CX-5 CX-7 CX-9 Miata RX-8
Mercedes C CL CLA CLK CLS E GLA GLK M Class
MINI Cooper
Nissan 350Z 370Z Altima Cube Frontier GT-R Juke Maxima Murano Rogue Sentra Titan
Scion FR-S FRS tC xA xB xD
Subaru BRZ Forester Impreza Legacy WRX STI
Toyota 4Runner Camry Corolla FJ Cruiser Highlander Prius RAV4 Sequoia Sienna Tacoma Tundra
Volkswagen Beetle CC Golf GTI Jetta Passat Rabbit, etc
- 2 pieces of 95mm size-specific lamp assembly rear/back opening dust and water-resistant seal cover caps with extended depth, perfect for securing your vehicle's lighting system
- Featuring an inner sealing/fitting diameter of 95mm (+/- 3mm) and a height of approximately 60mm, these high-quality, flexible, heat-resistant PVC rubber caps accommodate variations of +/- 3mm in the diameter of the lamp back opening hole fitting
- Seal the light assembly back opening and protect against water condensation, moisture, dust, and other unwanted elements such as spiders and insects from entering the housing, ensuring your lighting system remains in clean condition
- Ideal for upgrading or replacing the light seal cap when the original one is too small or too low, especially after upgrading to a bigger or longer size bulb
- To select the cap size you need, measure the outer diameter of the lamp opening and if it's over by 3mm of the cap size, go for the next size; if the fitting is slightly tight, you can stretch the cap, and if it's a bit loose, tighten it with a zip-tie or black tape; the soft rubber cap cover may deform during shipment but this won't affect its use
- 2 pieces of 95mm size-specific lamp assembly rear/back opening dust and water-resistant seal cover caps with extended depth, perfect for securing your vehicle's lighting system
- Featuring an inner sealing/fitting diameter of 95mm (+/- 3mm) and a height of approximately 60mm, these high-quality, flexible, heat-resistant PVC rubber caps accommodate variations of +/- 3mm in the diameter of the lamp back opening hole fitting
- Seal the light assembly back opening and protect against water condensation, moisture, dust, and other unwanted elements such as spiders and insects from entering the housing, ensuring your lighting system remains in clean condition
- Ideal for upgrading or replacing the light seal cap when the original one is too small or too low, especially after upgrading to a bigger or longer size bulb
- To select the cap size you need, measure the outer diameter of the lamp opening and if it's over by 3mm of the cap size, go for the next size; if the fitting is slightly tight, you can stretch the cap, and if it's a bit loose, tighten it with a zip-tie or black tape; the soft rubber cap cover may deform during shipment but this won't affect its use
