Parameter
Model: WS2812B 300 pixels LED strip
Light source: 5050 LED
Led Qty: 60pcs per meter
Wave length (NM): R/650nm; G/520nm; B/460nm
IC Model: WS2811 IC built in 5050 SMD
Gray level: 256
Color: full color 24-bit
View angle: 120°
Work Voltage: DC 5V
Power: 0.3W per LED
Waterproof rate: Not waterproof IP30
FPCB board color: White
Dimension: 5000*10*3mm
Life span: 50000hrs
Kindly note
1) You must use a 5V DC power supply to power these strips, do not use higher than 6V or you can destroy the entire strip.
2) Led strip is made by 50cm FPCB, so there is a solder point each 50cm on strip. But this minor flaw has no any bad effect on the strip's performance. In fact, most of the LED strips on the market are manufactured in half-meter lengths.
3) If you want the data sheet of WS2812B, please contact us, we will send it to your email.
Package:
1x 16.4ft 300 pixels WS2812B led strip (Power supply and controller are not included)
Related product links
5V 15A Power supply:
https://www.amazon.com/dp/B01LXN7MN3
SP105E Bluetooth Magic LED Controller:
https://www.amazon.com/dp/B01LW1J10W
SP103E Mini Wireless RF Remote Controller:
https://www.amazon.com/dp/B01HCHHM04
T1000S LED Controller:
https://www.amazon.com/dp/B01M4IX5FF
WS2812B addressable LED Strip:
https://www.amazon.com/dp/B00ZHB9M6A?th=1
WS2811 LED pixels string:
https://www.amazon.com/dp/B01AG923GI
- 【Individually Addressable LED】Each pixel can have its own color and brightness. You can control them individually and set them to any color or animation you want. 256 brightness display and 24-bit color display.
- 【Easy to program.】Works great with Arduino, FastLED library, Raspberry Pi, FadeCandy, T1000S etc. It can also be controlled by SP105E, SP103E, HC008 and other pre-programmed WS2811 controllers.
- 【Easy installation.】 It comes with self-adhesive 3M tape on its back, so you can fix it on any dry and flat surface without any screws and clips, the cloth is not a single piece there are seams in the middle.
- 【Great for DIY】 It comes with 3pin JST-SM connectors on both ends. Each LED can be cut off without damaging the rest strip. You can shorten, lengthen or bend it freely if you want.
- 【wide application】 It can be used to make led screen, led wall, advertising board and widely applied to hotel, KTV, bars, Outdoor advertising signs, wedding, party lighting and so on.
- 【Individually Addressable LED】Each pixel can have its own color and brightness. You can control them individually and set them to any color or animation you want. 256 brightness display and 24-bit color display.
- 【Easy to program.】Works great with Arduino, FastLED library, Raspberry Pi, FadeCandy, T1000S etc. It can also be controlled by SP105E, SP103E, HC008 and other pre-programmed WS2811 controllers.
- 【Easy installation.】 It comes with self-adhesive 3M tape on its back, so you can fix it on any dry and flat surface without any screws and clips, the cloth is not a single piece there are seams in the middle.
- 【Great for DIY】 It comes with 3pin JST-SM connectors on both ends. Each LED can be cut off without damaging the rest strip. You can shorten, lengthen or bend it freely if you want.
- 【wide application】 It can be used to make led screen, led wall, advertising board and widely applied to hotel, KTV, bars, Outdoor advertising signs, wedding, party lighting and so on.
