Description
When a HID kit is installed in newer car models or cars with a computer controlled unit, often there is a error code showing on the dash board or the HID lights keep flickering and would not stay on. This is due to the fact that the HID kit is triggering a bulb out warning signal in your car's computer control unit.
Features:
Brand new and high quality.
Solve the error information on the dash board.
Make your HID headlights stop flickering.
Get rid of computer error warning encountered during the installation of the HID kits.
Suitable for all cars that have computer controlled headlights.
Package Included:
2 x HID Error Canceller
It can solve the problems as below:
The indicator of the instrument panel lights when the headlight is used as Fault Light.
The indicator of the instrument panel doesn't light when the headlight is used as High Beam.
The Xenon lights flash when starting the engine.
The engine stops working when turning on the Xenon lights.
Eliminate the interference of the Ballast to the trip computer
Xenon lights don't light.
Xenon lights keep flashing after installation.
One of the Xenon light works, but the other one doesn't light.
Xenon lights automatically turn off after lighting up for few minutes.
Note: The Capacitor Harness can only install between the "BALLAST AND OEM HEADLIGHT HARNESS", it can not be installed anywhere else.
Warning: Some vehicles may have reverse polarity. Reverse polarity can cause a BOW to explode. We recommend wearing safety glasses and closing your hood before testing the BOW on your vehicle.
※ If there's any problem with the product, please feel free to contact us. We will replace it or refund you money. ※
- This product is hid xenon Anti-Flicker Warning Cancellers, only work for hid xenon, no work with headlight;if you buy wrong, please contact us first, thanks
- The voltage is 9-16V, it can work with 24V autos; and this product is normally used with 35W hid xenon kit, some 55w can not be used with it. the size of this anti-flicker is: 19cm x 4.8cm x 2.7cm - 7.5inch x 1.9inch x 1.1inch.
- Easy installaEasy installation, Just plug and play, no modification is needed. Available in all sizes. Confirm your bulb size at Osram Sylvania or Phillips websites or with the seller of your aftermarket projector headlight housing assemblies.tion, Just plug and play, no modification is needed.
- Work with single beam HID xenon kits, for example: H1, H3, H4, H7, H8, H9, H10, H11, 9005, 9006, 880, 881, 889.
- Installation Instruction: The special wire harness needs to be used with caution: Red wire needs connect to positive ( + ), black connect to negative ( - ). There is a capacitor on this wire harness to by-pass the error message signal and the capacitor is polarity sensitive, so the red and black wires need to be in the correct position. OTHERWISE THE CAPACITOR WILL BE BURNED. Please use a voltage meter to make sure the correct polarity before installation.
- This product is hid xenon Anti-Flicker Warning Cancellers, only work for hid xenon, no work with headlight;if you buy wrong, please contact us first, thanks
- The voltage is 9-16V, it can work with 24V autos; and this product is normally used with 35W hid xenon kit, some 55w can not be used with it. the size of this anti-flicker is: 19cm x 4.8cm x 2.7cm - 7.5inch x 1.9inch x 1.1inch.
- Easy installaEasy installation, Just plug and play, no modification is needed. Available in all sizes. Confirm your bulb size at Osram Sylvania or Phillips websites or with the seller of your aftermarket projector headlight housing assemblies.tion, Just plug and play, no modification is needed.
- Work with single beam HID xenon kits, for example: H1, H3, H4, H7, H8, H9, H10, H11, 9005, 9006, 880, 881, 889.
- Installation Instruction: The special wire harness needs to be used with caution: Red wire needs connect to positive ( + ), black connect to negative ( - ). There is a capacitor on this wire harness to by-pass the error message signal and the capacitor is polarity sensitive, so the red and black wires need to be in the correct position. OTHERWISE THE CAPACITOR WILL BE BURNED. Please use a voltage meter to make sure the correct polarity before installation.
